4432-T-B1 B 915【PDF 39/47 页】KIT DEV TEST EZRADIOPRO SI4432

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录49

35页 36页 37页 38页 [39页]40页 41页 42页 43页

Si4430/31/32-B1

Rev 1.1

the output from the D-S modulator. The tuning resolution is sufficient to tune to the commanded frequency with a

maximum accuracy of 312.5 Hz anywhere in the range between 240960 MHz.

5.6.1. VCO

The output of the VCO is automatically divided down to the correct output frequency depending on the hbsel and

fb[4:0] fields in "Register 75h. Frequency Band Select." In receive mode, the LO frequency is automatically shifted

downwards by the IF frequency of 937.5 kHz, allowing transmit and receive operation on the same frequency. The

VCO integrates the resonator inductor and tuning varactor, so no external VCO components are required.

The VCO uses a capacitance bank to cover the wide frequency range specified. The capacitance bank will

automatically be calibrated every time the synthesizer is enabled. In certain fast hopping applications this might not

be desirable so the VCO calibration may be skipped by setting the appropriate register.

5.7. Power Amplifier

The Si4432 contains an internal integrated power amplifier (PA) capable of transmitting at output levels between +1

and +20 dBm. The Si4431/4430 contains a PA which is capable of transmitting output levels between 8 to

+13 dBm. The PA design is single-ended and is implemented as a two stage class CE amplifier with a high

efficiency when transmitting at maximum power. The PA efficiency can only be optimized at one power level.

Changing the output power by adjusting txpow[2:0] will scale both the output power and current but the efficiency

will not remain constant. The PA output is ramped up and down to prevent unwanted spectral splatter.

In the Si4431, the TX and RX may be tied directly. See the TX/RX direct-tie reference design available on the

Silicon Labs website for more details. When the direct tie is used, the lna_sw bit in Register 6Dh. TX Power must be

set to 1.

5.7.1. Output Power Selection

The output power is configurable in 3 dB steps with the txpow[2:0] field in "Register 6Dh. TX Power." Extra output

power can allow the use of a cheaper smaller antenna, greatly reducing the overall BOM cost. The higher power

setting of the chip achieves maximum possible range, but of course comes at the cost of higher TX current

consumption. However, depending on the duty cycle of the system, the effect on battery life may be insignificant.

Contact Silicon Labs Support for help in evaluating this tradeoff.

Add R/W Function/D

escription

POR

Def.

6D R/W

TX Power

reserved

reserved lna_sw txpow[2] txpow[1] txpow[0] 18h

txpow[2:0]

Si4432 Output Power

000

+1 dBm

001

+2 dBm

010

+5 dBm

011

+8 dBm

100

+11 dBm

101

+14 dBm

110

+17 dBm

111

+20 dBm

txpow[2:0]

Si4431/30 Output Power

000

8 dBm

001

5 dBm

010

2 dBm

011

+1 dBm

100

+4 dBm

101

+7 dBm

110

+10 dBm

111

+13 dBm

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式